SD-Internet Provisioning
Pre-configuration (Completed by Adaptiv Networks)
Follow the steps in this section only if an unconfigured device was shipped (to the partner) and had to be configured from factory defaults. If provisioning of the device has been done in advance, skip to the next section.
In pre-configuration, Adaptiv | Edge is provisioned with network information required to precisely communicate within the network. Provisioning is completed through Adaptiv | Cloud Portal before the device is physically set up and connected to the underlay links. If all the site-provided underlay links are static IP addresses, we recommend completing the pre-configuration process before the device is shipped out.
To pre-configure the device, log in to the Portal and follow the steps below.
- Navigate to the Order Management tab and locate the order in the Order Management table.
- Open the order from the table and
- For Submitted orders, review order details, and click Configure at the bottom of the page.
- For Open orders, first, submit it and then continue with pre-configuration.
- For Submitted orders, review order details, and click Configure at the bottom of the page.
- On the Configuration page, fill out the following information and click Next.
If the MAC Address or Serial Number were already provided during the order entry, click Load CPE identification from order info to auto-populate these fields.- POP – Adaptiv | Gateway closest to the installation site
Gateway ATL (Atlanta) DEN (Denver) DFW (Dallas Fort Worth) JFK (New York) LAX (Los Angeles) ORD (Chicago) SEA (Seattle) YTO (Toronto) AUK ( United Kingdom)
ADE ( Germany) - Concentrator pair – Pairs of Concentrators compatible with the selected Gateway
- CIDR – Select a subnet mask for required IP addresses.
If a CIDR value is provided in the Network Details section of the order form, it is updated here.Value Description /32
- Default prefix configuration that assigns a single public IP address to the Edge device; useful in device management and Internet NAT traffic
- Automatically disables DMZ support
- Not applicable for customers selecting public DHCP server configuration. Please contact the Support Team for further assistance.
/30
- Select this prefix if a customer site requires on-premise Firewall Support.
/29 /28 /27
- A prefix configuration greater than /30 is available. Please contact your Sales Account Manager for more information and pricing plans.
- Prefix – Prefix compatible with the Gateway
- OS Version – Select 7.2.1 or the latest
- POP – Adaptiv | Gateway closest to the installation site
- MAC Address – Enter the MAC Address for the Edge device
- Serial Number – Enter the serial number located on the back of the Edge device

The Portal throws a validation error if the MAC Address for this device is already in use. To proceed with the installation, the users must deprovision the device.
- On the Confirm Details page, verify the device and network information and select the checkbox - Please confirm all the information is correct. After selecting the checkbox, click Install.

If you note that any information on this page is incorrect, deprovision the device, and reopen the order to continue with the installation.
See Order Deprovisioning and Cancelation.
After completing the pre-configuration, the next step is physically connecting the Edge device to the underlay links. Once the device is online and running, follow the steps listed here to push the configuration through Adaptiv | Cloud Portal.
Connecting Adaptiv | Edge and Internet links
In this step, a network technician or staff at the customer site physically sets up the Edge device by connecting it to the underlay broadband (ISP) links. The users are recommended to follow the suggested best practices to connect the Edge device to underlay links. To enable a rapid install of the Edge device, follow the step-by-step instructions listed in the QuickStart Guides below.
- Adaptiv | Edge E-40 QuickStart Guide
- Adaptiv | Edge E-60 QuickStart Guide
- Adaptiv | Edge Ai-400 QuickStart Guide
- Adaptiv | Edge Ai-600 QuickStart Guide
Provisioning with Adaptiv | Cloud Portal
This step is completed in Adaptiv | Cloud Portal and the configured network information is pushed to the Edge device and links are calibrated.
- Navigate to the Order Management tab and locate the order.
- On the Provisioning page, check the Primary CPE Installation Process value.
- Online indicates that the device is online
- Offline indicates that the device is not online or properly connected to the underlay links. Click Refresh CPE Status and check if the status changes to Online.
If the device fails to come online, contact Adaptiv Networks Engineers.
- To push the configuration to the device, click Run all.
The system takes around 5-10 minutes to complete the configuration. - After the Edge device has been successfully provisioned, click Next.
- On the Config & Calibration page, Click Save Configuration and Finish.
6.Upon successful installation, the Portal displays the message "Save Configuration success. Installation complete."
TERMS OF USE | ANTI SPAM | PRIVACY POLICY | USER LICENSE AGREEMENT | PATENTS