---
title: "SD-WAN Provisioning "
id: "sd-wan-provisioning"
project: "Adaptiv | Cloud Support Publication"
url: "https://docs.scalecomputing.com/articles/adaptiv-cloud-support-publication/sd-wan-provisioning"
keywords:
  - "Adaptiv | Edge Ai-400 QuickStart Guide"
  - "Adaptiv | Edge Ai-600 QuickStart Guide"
  - "Adaptiv | Edge E-40 QuickStart Guide"
  - "Adaptiv | Edge E-60 QuickStart Guide"
  - "Calibration"
  - "Connecting hardware"
  - "Pre-Configuration"
  - "Provisioning Adaptiv | Edge"
  - "Remote CPE LAN"
  - "SD-WAN Installation"
updated: 2026-03-02T20:02:09Z
---

# SD\-WAN Provisioning 

# **SD-WAN Provisioning**

This topic outlines the procedures for installing SD-WAN service on Adaptiv | Edge. Adaptiv Network recommends users follow the suggested [best practices](/articles/adaptiv-cloud-support-publication/installation-best-practices)for a frictionless installation.

In SD-WAN installation, a partner must submit an individual [order](/articles/adaptiv-cloud-support-publication/processing-orders/a/h2_0) for each site. Additionally, they must provide the CPE LAN Subnet information which is information about all the subnets reachable to that site. Although SD-WAN involves multiple sites, all the sites might not be installed at the same time. Each order is provisioned and installed individually.

* [Pre-configuration (Completed by Adaptiv Networks)](/articles/adaptiv-cloud-support-publication/sd-wan-provisioning/a/h2_1891175064)
* [Connecting Adaptiv | Edge and Internet links](/articles/adaptiv-cloud-support-publication/sd-wan-provisioning/a/h2_1644201065)
* [Provisioning with Adaptiv | Cloud Portal](/articles/adaptiv-cloud-support-publication/sd-wan-provisioning/a/h2_900188138)
* [Configuring remote CPE LAN](/articles/adaptiv-cloud-support-publication/sd-wan-provisioning/a/h2__125130174)

## **Pre-configuration****(Completed by Adaptiv Networks)**

*Follow the steps in this section only if an unconfigured device was shipped (to the partner) and had to be configured from factory defaults. If provisioning of the device has been done in advance, skip to the next section.*

In pre-configuration, the network information is configured for the Edge device. When provisioned, it can communicate across the Adaptiv | Core to speak to other Edge devices deployed at different customer sites. If all the site-provided underlay links are static IP addresses, we recommend completing the pre-configuration process before the device is shipped out.

To pre-configure the device, log in to the Portal and follow the steps below.

1. Navigate to the **Order Management**tab and locate the order in the Order Management table.
2. Open the order from the table and 
    * For Submitted orders, review order details, and click **Configure** at the bottom of the page.
    * For **Open** orders, first, submit it and then continue with the pre-configuration.
3. On the Configuration page, fill out the following information and click **Next**.
If the MAC Address or Serial Number were already provided during the order entry, click **Load CPE identification from order info** to auto-populate these fields.

    * **POP** – Adaptiv | Gateway closest to the installation site
[+] [Adaptiv | Gateway Selection](javascript:void%280%29)
[-] [Adaptiv | Gateway Selection](javascript:void%280%29)
| **Gateway** |
        | --- |
        | ATL (Atlanta) |
        | DEN (Denver) |
        | DFW (Dallas Fort Worth) |
        | JFK (New York) |
        | LAX (Los Angeles) |
        | ORD (Chicago) |
        | SEA (Seattle) |
        | YTO (Toronto) |
        | AUK (United Kingdom) |
        | ADE (Germany) |
    * **Concentrator pair** – Pairs of Concentrators compatible with the selected Gateway
    * **CIDR** – Select a subnet mask for required IP addresses.
If a CIDR value is provided in the **Network Details**section of the order form, it is updated here. 

        | **Value** | **Description** |
        | --- | --- |
        | /32 | <ul><li><span style="font-size: 16px; font-family: Arial, &quot;Helvetica Neue&quot;, Helvetica, sans-serif;">Default prefix configuration that assigns a single public IP address to the Edge device; useful in device management and Internet NAT traffic</span></li><li><span style="font-size: 16px; font-family: Arial, &quot;Helvetica Neue&quot;, Helvetica, sans-serif;">Automatically disables DMZ support</span></li><li><span style="font-size: 16px; font-family: Arial, &quot;Helvetica Neue&quot;, Helvetica, sans-serif;">Not applicable for customers selecting public DHCP server configuration. Please contact the&#160;<a href="mailto:support@adaptiv-networks.com?subject=Assistance to select Prefix Configuration" target="_top">Support Team</a>&#160;for further assistance.</span></li></ul> |
        | /30 | <ul><li><span style="font-size: 16px; font-family: Arial, &quot;Helvetica Neue&quot;, Helvetica, sans-serif;">Select this prefix if a customer site requires on-premise Firewall Support.</span></li></ul> |
        | /29 /28 /27 | <ul><li><span style="font-size: 16px; font-family: Arial, &quot;Helvetica Neue&quot;, Helvetica, sans-serif;">A prefix configuration greater than /30 is available. Please contact your Sales Account manager for more information and pricing plans.</span></li></ul> |
    * **Prefix** – Prefix compatible with the Gateway.
    * **OS Version**– Select **7.2.1**or the latest

* **MAC Address** – MAC Address of the Edge device
* **Serial Number******– Enter the serial number located on the back of the Edge device

    | ![Information](/resources/Storage/adaptiv-cloud-support-publication/adaptiv-cloud-support-publication/Information.jpg) | The Portal throws a validation error if the MAC Address for this device is already in use. To proceed with the installation, the users must deprovision the device. |
    | --- | --- |
* Please confirm all the information is correct on the Confirm Details page, verify the device and network information, and select the checkbox. After selecting the checkbox, click **Install**.

    | ![Warning](/resources/Storage/adaptiv-cloud-support-publication/adaptiv-cloud-support-publication/Warning.svg.jpg) | If you note that any information on this page is incorrect, deprovision the device, and reopen the order to continue with the installation. See [Order Deprovisioining and Cancelation](/articles/adaptiv-cloud-support-publication/order-deprovisioning-and-cancelation). |
    | --- | --- |

After completing the pre-configuration, the next step is physically connecting the Edge device to the underlay links. Once the device is online and running, follow the steps listed [here](/smart/support/sd-wan-installation/a/h2_900188138)to push the configuration through Adaptiv | Cloud Portal.

## **Connecting Adaptiv | Edge and Internet links**

In this step, a network technician or staff at the customer site physically sets up the Edge device by connecting it to the underlay broadband links. The users are recommended to follow the suggested [best practices](/articles/adaptiv-cloud-support-publication/installation-best-practices) to connect the Edge device to underlay links. To enable a rapid install of the Edge device, follow the step-by-step instructions listed in the QuickStart Guides below.

* [Adaptiv | Edge E-40 QuickStart Guide](/smart/project-e40/adaptiv-edge-e-40-install-guide-7-x)
* [Adaptiv | Edge E-60 QuickStart Guide](/smart/project-e60-install-guide/adaptiv-edge-e-60-install-guide-7-x)
* [Adaptiv | Edge Ai-400 QuickStart Guide](/smart/project-ai-400-install-guide/adaptiv-edge-ai-400-quickstart-guide)
* [Adaptiv | Edge Ai-600 QuickStart Guide](/smart/project-ai-600-install-guide/adaptiv-edge-ai-600-quickstart-guide)

## **Provisioning with Adaptiv | Cloud Portal**

This step is completed in Adaptiv | Cloud Portal and the configured network information is pushed to the Edge device and links are calibrated.

1. Navigate to the **Order Management**tab and locate the order.
2. On the provisioning page, check the **Primary CPE Installation Process** value.
    * **Online** indicates that the device is online
    * **Offline** indicates that the device is not online or properly connected to the underlay links. Click **Refresh CPE Status** and check if the status changes to **Online**. 
If the device remains Offline, contact Adpativ Networks Engineers.
3. To push the configuration to the device, click **Run all**.
The system takes around 5-10 minutes to complete the configuration.
4. After the configuration is successfully saved, click **Next**.
5. On the Config & Calibration page, Click **Save Configuration and Finish.**

6. Upon successful installation, the portal displays the message **"Save Configuration success. Installation complete."**

## **Configuring remote CPE LAN**

After the individual sites in the SD-WAN network are installed, they must be synchronized to complete site-to-site connectivity. The synchronization process must be carried out every time a new site is added to the network. This process is completed on the **SD-WAN** page in the **CPE Management**tab. The **Remote CPE LAN**table on this page identifies the CPE LAN IP address. Depending on the synchronization status of the IP address, it is assigned a color.

* **Blue** – This color indicates the configured routes to the remote sites.
* **Green** – This color indicates the remote sites that are provisioned and successfully configured on the local Edge device
* **Red** – This color indicates the provisioned remote sites but not successfully configured on the local Edge device.

1. Navigate to the **CPE Management** tab and enter the hostname.
2. After the **Overview** page appears with the site data, click **SD-WAN**.
3. On the **SD-WAN**page, locate the **Remote CPE LAN** table.
4. Select the checkbox next to the site where the **Expected CPE LAN Remote** IP address is not configured (as indicated by the red color).
5. Click **Synchronize**.

### Updating remote CPE LAN

Users can add a new CPE LAN or delete an existing one from the **Remote CPE LAN** table.

* To add a new subnet, click ![](/resources/Storage/adaptiv-cloud-support-publication/Adaptiv%20Cloud%20Portal_New/Edit_SD-WAN.png)![](/resources/Storage/adaptiv-cloud1/Edit%20CPE%20LAN.jpg)From the **Select CPE hostname**dropdown menu, select the CPE to which you want to add the subnet. Type the Subnet address in the **Select CPE LAN subnets**dropdown menu and click **Accept**. This step automatically synchronizes the added subnet to all SD-WAN sites. Confirm the addition of a new subnet by locating it in both the **Configured CPE LAN Remote** and **Expected CPE LAN Remote** columns.
* To delete an existing CPE LAN subnet, click ![](/resources/Storage/adaptiv-cloud-support-publication/Adaptiv%20Cloud%20Portal_New/Edit_SD-WAN.png). From the **Select CPE hostname**dropdown menu, select the CPE for which you want to delete the subnet. In the **Select CPE LAN subnets** dropdown menu, deselect the subnet address from the list and click **Accept.**This step automatically synchronizes the removal of this subnet from all SD-WAN sites. Confirm by verifying the subnet is removed from both the **Configured CPE LAN Remote** and **Expected CPE LAN Remote** columns.

* * *

[TERMS OF USE](https://www.adaptiv-networks.com/terms-of-use) | [ANTI SPAM](https://www.adaptiv-networks.com/anti-spam)| [PRIVACY POLICY](https://www.adaptiv-networks.com/privacy)| [USER LICENSE AGREEMENT](https://www.adaptiv-networks.com/user-license-agreement) | [PATENTS](https://www.adaptiv-networks.com/patents)
Copyright © 2026 Adaptiv Networks, Inc. [Send Feedback](mailto:docs@adaptiv-networks.com?subject=Feedback)